2456820000 ACT20P-BRIDGE-P | Weidmüller Product Catalogue

ACT20P-BRIDGE-P

example for DIP switch setting (with ACT20 tool)

General ordering data
Version	Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V
Order No.	2456820000
Type	ACT20P-BRIDGE-P
GTIN (EAN)	4050118471762
Qty.	1 pc(s).

Dimensions and weights
Depth	113.6 mm
Depth (inches)	4.472 inch
Height	127.1 mm
Height (inches)	5.004 inch
Width	22.5 mm
Width (inches)	0.886 inch
Net weight	205 g

Temperatures
Storage temperature	-40 °C...85 °C
Operating temperature	-20 °C...60 °C
Humidity at operating temperature	0...95 % (no condensation)
Humidity	10…90 %, no condensation

Probability of failure
SIL in compliance with IEC 61508	None

Environmental Product Compliance
REACH SVHC	Lead 7439-92-1
SCIP	2f6dd957-421a-46db-a0c2-cf1609156924

Input
Bridge sensitivity	1.0 mV / V to 5.0 mV / V
Bridge supply voltage	5 V or 10 V
Input signal	±10 mV / ±20 mV / ±30 mV / ±50 mV
Number of inputs	1
Sensor	Strain gauge resistance, Resistance measurement, Total resistance of all parallel resistance measuring bridges: min. 87 Ω
Sensor supply	120 mA @ 10 V (= 4 x 350 Ω bridge resistors)

Output
Load impedance current	≤ 600 Ω
Output current	0…22 mA (adjustable)
Output voltage, note	0…11 V (adjustable)
Type	active, connected control must be passive
load impedance voltage	600 Ω

General data
Accuracy	<0.05 % of measuring range
Configuration	DIP switch and button
Linearity	Typically ± 0.05 % of signal range
Long-term drift	0.1 % / 10.000 h
Power consumption	3 W @ 24 V DC
Protection degree	IP20
Rail	TS 35
Step response time	<400 ms (10…90 %)
Temperature coefficient	typ. 0.005 % / °C
Voltage supply	10…60 V DC

Insulation coordination
EMC standards	EN 61326
Insulation voltage	5.7 kV (input / output, input / supply)
Pollution severity	2
Rated voltage	300 V
Surge voltage category	III

Connection data
Type of connection	PUSH IN
Tightening torque, min.	0.4 Nm
Tightening torque, max.	0.6 Nm
Clamping range, rated connection	2.5 mm²
Clamping range, min.	0.5 mm²
Clamping range, max.	2.5 mm²
Wire connection cross section AWG, min.	AWG 26
Wire connection cross section AWG, max.	AWG 14
Wire cross-section, solid, min.	0.2 mm²
Wire cross-section, solid, max.	2.5 mm²
Wire connection cross section, finely stranded, min.	0.2 mm²
Wire connection cross section, finely stranded, max.	2.5 mm²
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, min.	0.2 mm²
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, max.	2.5 mm²

Important note
Product information	The ACT20P-BRIDGE-P bridge measuring transducer converts measuring bridge voltages into standard signals. Buttons are used for adjustment to the measuring bridge connected. The bridge measuring transducer can supply up to 4 parallel-connected measuring bridges each with 350 Ω. The device supports simple compensation of the tare weight with a separate input for an external button or an external PLC signal. The power supply is galvanically isolated from input and output (3-way isolation).T Features 4-wire and 6-wire measurement Supply of up to 4 parallel-connected measuring bridges each with 350 Ω Input and output ranges can be adjusted via DIP switches Tare compensation via external button or PLC signal Front LED indicates operation status 3-way galvanic isolation between input, output and power supply

Downloads
Approval/Certificate/Document of Conformity	Declaration of Conformity
Engineering Data	CAD data -- STEP
Eplan Data Portal	Eplan data
CADENAS eCATALOG	CAX data
Software	DIP switch configuration tool
User Documentation	Quickstart guide german Instruction sheet Quickstart guide english
Catalogues	Catalogues in PDF-format

Classifications
ETIM 6.0	EC002653
ETIM 7.0	EC002653
ETIM 8.0	EC002653
ETIM 9.0	EC002653
ECLASS 9.0	27-21-01-20
ECLASS 9.1	27-21-01-20
ECLASS 10.0	27-21-01-20
ECLASS 11.0	27-21-01-20
ECLASS 12.0	27-21-01-20
ECLASS 13.0	27-21-01-20

Approvals
Approvals
Approvals	CULUS;
ROHS	Conform

Related products:

	Order No.: 1067250000 Type of connection: Screw connection Type: ACT20P BRIDGE	Version: Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V
		PDF data sheet Add to Inquiry List

General ordering data

Version	Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V
Order No.	2456820000
Type	ACT20P-BRIDGE-P
GTIN (EAN)	4050118471762
Qty.	1 pc(s).

Dimensions and weights

Depth	113.6 mm
Depth (inches)	4.472 inch
Height	127.1 mm
Height (inches)	5.004 inch
Width	22.5 mm
Width (inches)	0.886 inch
Net weight	205 g

Temperatures

Storage temperature	-40 °C...85 °C
Operating temperature	-20 °C...60 °C
Humidity at operating temperature	0...95 % (no condensation)
Humidity	10…90 %, no condensation

Environmental Product Compliance

REACH SVHC	Lead 7439-92-1
SCIP	2f6dd957-421a-46db-a0c2-cf1609156924

Input

Bridge sensitivity	1.0 mV / V to 5.0 mV / V
Bridge supply voltage	5 V or 10 V
Input signal	±10 mV / ±20 mV / ±30 mV / ±50 mV
Number of inputs	1
Sensor	Strain gauge resistance, Resistance measurement, Total resistance of all parallel resistance measuring bridges: min. 87 Ω
Sensor supply	120 mA @ 10 V (= 4 x 350 Ω bridge resistors)

Output

Load impedance current	≤ 600 Ω
Output current	0…22 mA (adjustable)
Output voltage, note	0…11 V (adjustable)
Type	active, connected control must be passive
load impedance voltage	600 Ω

General data

Accuracy	<0.05 % of measuring range
Configuration	DIP switch and button
Linearity	Typically ± 0.05 % of signal range
Long-term drift	0.1 % / 10.000 h
Power consumption	3 W @ 24 V DC
Protection degree	IP20
Rail	TS 35
Step response time	<400 ms (10…90 %)
Temperature coefficient	typ. 0.005 % / °C
Voltage supply	10…60 V DC

Insulation coordination

EMC standards	EN 61326
Insulation voltage	5.7 kV (input / output, input / supply)
Pollution severity	2
Rated voltage	300 V
Surge voltage category	III

Connection data

Type of connection	PUSH IN
Tightening torque, min.	0.4 Nm
Tightening torque, max.	0.6 Nm
Clamping range, rated connection	2.5 mm²
Clamping range, min.	0.5 mm²
Clamping range, max.	2.5 mm²
Wire connection cross section AWG, min.	AWG 26
Wire connection cross section AWG, max.	AWG 14
Wire cross-section, solid, min.	0.2 mm²
Wire cross-section, solid, max.	2.5 mm²
Wire connection cross section, finely stranded, min.	0.2 mm²
Wire connection cross section, finely stranded, max.	2.5 mm²
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, min.	0.2 mm²
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, max.	2.5 mm²

The ACT20P-BRIDGE-P bridge measuring transducer converts measuring bridge voltages into standard signals. Buttons are used for adjustment to the measuring bridge connected. The bridge measuring transducer can supply up to 4 parallel-connected measuring bridges each with 350 Ω. The device supports simple compensation of the tare weight with a separate input for an external button or an external PLC signal. The power supply is galvanically isolated from input and output (3-way isolation).T

Features

4-wire and 6-wire measurement
Supply of up to 4 parallel-connected measuring bridges each with 350 Ω
Input and output ranges can be adjusted via DIP switches
Tare compensation via external button or PLC signal
Front LED indicates operation status
3-way galvanic isolation between input, output and power supply

Downloads

Approval/Certificate/Document of Conformity	Declaration of Conformity
Engineering Data	CAD data -- STEP
Eplan Data Portal	Eplan data
CADENAS eCATALOG	CAX data
Software	DIP switch configuration tool
User Documentation	Quickstart guide german Instruction sheet Quickstart guide english
Catalogues	Catalogues in PDF-format

Classifications

ETIM 6.0	EC002653
ETIM 7.0	EC002653
ETIM 8.0	EC002653
ETIM 9.0	EC002653
ECLASS 9.0	27-21-01-20
ECLASS 9.1	27-21-01-20
ECLASS 10.0	27-21-01-20
ECLASS 11.0	27-21-01-20
ECLASS 12.0	27-21-01-20
ECLASS 13.0	27-21-01-20

Approvals

Approvals
Approvals	CULUS;
ROHS	Conform

Related products

	Order No.: 1067250000 Type of connection: Screw connection Type: ACT20P BRIDGE	Version: Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V
		PDF data sheet Add to Inquiry List

	Engineering Data
	Add to inquiry list / Ask about product
	PDF data sheet
	Individual parts
	Accessories
	Related products
	Print view