8560740000 WAS4 PRO DC/DC | Weidmüller Product Catalogue

WAS4 PRO DC/DC Product is no longer availableData sheet for information only

General ordering data
Version	Signal converter/insulator, Screw connection
Order No.	8560740000
Type	WAS4 PRO DC/DC
GTIN (EAN)	4032248207350
Qty.	1 pc(s).
Delivery status	This article will no longer be available in the future.
Available until	2022-03-30
Alternative product	1481970000

Dimensions and weights
Depth	112.4 mm
Depth (inches)	4.425 inch
Width	12.5 mm
Width (inches)	0.492 inch
Length	92.4 mm
Length (inches)	3.638 inch
Net weight	132.2 g

Temperatures
Storage temperature	-40 °C...85 °C
Operating temperature	0 °C...70 °C
Humidity at operating temperature	0...95 % (no condensation)

Probability of failure
SIL in compliance with IEC 61508	None
MTBF	76 a
MTTF	76 a

Environmental Product Compliance
REACH SVHC	Lead 7439-92-1
SCIP	b25f3b7c-b874-4a4e-a8b2-4f423a7e2a65

Input
Input current	configurable, ± 0.1mA...± 100 mA
Input resistance, current	<5 mA: approx. 100 Ω; >5 mA: approx. 5 Ω
Input resistance, voltage	approx. 1 MΩ
Input voltage	configurable, ±20 mV…±200 V
Number of inputs	1

Output
Cut-off frequency (-3 dB)	> 10 kHz/ <10 Hz
Load impedance current	≤ 600 Ω
Number of outputs	1
Offset current	20 µA
Offset voltage	10 mV
Output current	0...±20 mA
Output voltage, note	0...±10 V
load impedance voltage	≥ 1 kΩ

Output (analogue)
Output current	0...±20 mA

General data
Accuracy	<0.1 % of end value, + Offset 0.1 %
Configuration	DIP switch and potentiometer, with reference voltage/current sources
Galvanic isolation	3-way isolator
Power consumption	ca. 1 W
Rail	TS 35
Step response time	120 µs at limiting-frequency setting > 10 kHz, 75 ms at limiting-frequency setting <10 Hz
Temperature coefficient	≤ 60 ppm/K of final value
Voltage supply	22…230 V AC/DC +10 %

Insulation coordination
EMC standards	DIN EN 61326, EN 61000-6 /-2, EN 61709 (SN 29500) MTBF
Galvanic isolation	3-way isolator
Impulse withstand voltage	5 kV, 1.2/50 µs (IEC 255-4)
Insulation voltage	4 kV_eff
Insulation voltage input or output/rail	4 kV_eff
Insulation voltage input or output/supply	4 kV_eff
Pollution severity	2
Rated voltage	600 V
Surge voltage category	III

Connection data
Type of connection	Screw connection
Stripping length, rated connection	7 mm
Tightening torque, min.	0.4 Nm
Tightening torque, max.	0.5 Nm
Clamping range, rated connection	2.5 mm²
Clamping range, min.	0.5 mm²
Clamping range, max.	2.5 mm²

Downloads
Approval/Certificate/Document of Conformity	Application notes -- Declaration of Conformity
Eplan Data Portal	Eplan data
WSCAD Universe	WSCAD data
Software	Software -- WaveTool.zip
User Documentation	Instruction sheet
Catalogues	Catalogues in PDF-format

Classifications
ETIM 6.0	EC002653
ETIM 7.0	EC002653
ETIM 8.0	EC002653
ETIM 9.0	EC002653
ECLASS 9.0	27-21-01-20
ECLASS 9.1	27-21-01-20
ECLASS 10.0	27-21-01-20
ECLASS 11.0	27-21-01-20
ECLASS 12.0	27-21-01-20
ECLASS 13.0	27-21-01-20

Tender specification sheets
Long specification	Standard signal isolating converter, Zero/span compensation, calibrated selection 1-channel signal isolating converter: with 12.5 mm width and external power supply for transmitting and isolating analogue DC current (± 0.1 to ± 100 mA) and voltage signals (± 20 mV to ± 200 V). Add-on housing for TS35 rail mounting Dimensions: L/W/H 92.4/ 12.5/ 112.4 mm Screw connection/ Nominal cross-section 2.5 mm²Protection degree: IP 20 Input +/- 20mV...+/- 200 V, +/- 0.1 mA...+/- 100 mA Output 0 … +/- 10 V, 0...+/- 20 mA Selection range calibrated selection with DIP switches/ 440 ranges Front-side calibration zero/span potentiometer Transmission error < 0,2% v. E. Limit frequency 10 Hz / 10 kHz adjustable Auxiliary power 22...230 V AC/DC +/- 10% Power loss approx. 1 W Ambient temperature range -10 °C...+70 °C Secure isolation EN 50178, 3-way isolation up to 4 kV AC/DC of all circuits against each other Test voltage 5 kV (1.2/50 us) Working voltage 600 V AC/DC at overvoltage category III and pollution degree 2 Approvals cULus, GL Type WAS4 PRO DC/DC
Short specification	Standard signal isolating converter, Zero/span compensation, calibrated selection 1-channel signal isolating converter: with 12.5 mm width and external power supply for transmitting and isolating analogue DC current (± 0.1 to ± 100 mA) and voltage signals.

Approvals
Approvals
ROHS	Conform
UL File Number Search	UL Website
Certificate no. (cULus)	E141197
Certificate no. (cULusEX)	E346097

General ordering data

Version	Signal converter/insulator, Screw connection
Order No.	8560740000
Type	WAS4 PRO DC/DC
GTIN (EAN)	4032248207350
Qty.	1 pc(s).
Delivery status	This article will no longer be available in the future.
Available until	2022-03-30
Alternative product	1481970000

Dimensions and weights

Depth	112.4 mm
Depth (inches)	4.425 inch
Width	12.5 mm
Width (inches)	0.492 inch
Length	92.4 mm
Length (inches)	3.638 inch
Net weight	132.2 g

Temperatures

Storage temperature	-40 °C...85 °C
Operating temperature	0 °C...70 °C
Humidity at operating temperature	0...95 % (no condensation)

Probability of failure

SIL in compliance with IEC 61508	None
MTBF	76 a
MTTF	76 a

Environmental Product Compliance

REACH SVHC	Lead 7439-92-1
SCIP	b25f3b7c-b874-4a4e-a8b2-4f423a7e2a65

Input

Input current	configurable, ± 0.1mA...± 100 mA
Input resistance, current	<5 mA: approx. 100 Ω; >5 mA: approx. 5 Ω
Input resistance, voltage	approx. 1 MΩ
Input voltage	configurable, ±20 mV…±200 V
Number of inputs	1

Output

Cut-off frequency (-3 dB)	> 10 kHz/ <10 Hz
Load impedance current	≤ 600 Ω
Number of outputs	1
Offset current	20 µA
Offset voltage	10 mV
Output current	0...±20 mA
Output voltage, note	0...±10 V
load impedance voltage	≥ 1 kΩ

General data

Accuracy	<0.1 % of end value, + Offset 0.1 %
Configuration	DIP switch and potentiometer, with reference voltage/current sources
Galvanic isolation	3-way isolator
Power consumption	ca. 1 W
Rail	TS 35
Step response time	120 µs at limiting-frequency setting > 10 kHz, 75 ms at limiting-frequency setting <10 Hz
Temperature coefficient	≤ 60 ppm/K of final value
Voltage supply	22…230 V AC/DC +10 %

Insulation coordination

EMC standards	DIN EN 61326, EN 61000-6 /-2, EN 61709 (SN 29500) MTBF
Galvanic isolation	3-way isolator
Impulse withstand voltage	5 kV, 1.2/50 µs (IEC 255-4)
Insulation voltage	4 kV_eff
Insulation voltage input or output/rail	4 kV_eff
Insulation voltage input or output/supply	4 kV_eff
Pollution severity	2
Rated voltage	600 V
Surge voltage category	III

Connection data

Type of connection	Screw connection
Stripping length, rated connection	7 mm
Tightening torque, min.	0.4 Nm
Tightening torque, max.	0.5 Nm
Clamping range, rated connection	2.5 mm²
Clamping range, min.	0.5 mm²
Clamping range, max.	2.5 mm²

Downloads

Approval/Certificate/Document of Conformity	Application notes -- Declaration of Conformity
Eplan Data Portal	Eplan data
WSCAD Universe	WSCAD data
Software	Software -- WaveTool.zip
User Documentation	Instruction sheet
Catalogues	Catalogues in PDF-format

Classifications

ETIM 6.0	EC002653
ETIM 7.0	EC002653
ETIM 8.0	EC002653
ETIM 9.0	EC002653
ECLASS 9.0	27-21-01-20
ECLASS 9.1	27-21-01-20
ECLASS 10.0	27-21-01-20
ECLASS 11.0	27-21-01-20
ECLASS 12.0	27-21-01-20
ECLASS 13.0	27-21-01-20

Standard signal isolating converter, Zero/span compensation, calibrated selection 1-channel signal isolating converter: with 12.5 mm width and external power supply for transmitting and isolating analogue DC current (± 0.1 to ± 100 mA) and voltage signals (± 20 mV to ± 200 V).

Add-on housing for TS35 rail mounting
Dimensions: L/W/H 92.4/ 12.5/ 112.4 mm
Screw connection/ Nominal cross-section 2.5 mm²Protection degree: IP 20

Input                       +/- 20mV...+/- 200 V, +/- 0.1 mA...+/- 100 mA
Output                                             0 … +/- 10 V, 0...+/- 20 mA
Selection range                             calibrated selection with DIP switches/ 440 ranges
Front-side calibration zero/span potentiometer
Transmission error               < 0,2% v. E.
Limit frequency 10 Hz / 10 kHz adjustable
Auxiliary power                                     22...230 V AC/DC +/- 10%
Power loss approx. 1 W
Ambient
temperature range -10 °C...+70 °C

Secure isolation                   EN 50178, 3-way isolation up to 4 kV AC/DC of all circuits against each other
Test voltage                               5 kV (1.2/50 us)
Working voltage                     600 V AC/DC at overvoltage category III and pollution degree 2
Approvals cULus, GL

Type WAS4 PRO DC/DC

Short specification

Approvals

Approvals
ROHS	Conform
UL File Number Search	UL Website
Certificate no. (cULus)	E141197
Certificate no. (cULusEX)	E346097

Related products

	Add to inquiry list / Ask about product
	PDF data sheet
	Accessories
	Related products
	Print view

Related products: