Monitoring component for AC currents up to 10A with 4...20 mA loop feed and electrical isolation Current monitoring component in 22.5 mm width for recording 50/ 60 Hz AC currents 0...1 A / 0...5 A / 0...10 A. Input range can be selected using DIP switches. Power is fed to the component via the 4...20 mA current loop on the output side. The input and output circuits have 6 kV of electrical isolation. Approved for ATEX Zone2 and UL C1 D2 applications.
Add-on housing for TS35 rail mounting Dimensions: L/W/H 72/ 22.5/ 92.4 mm Screw connection / Nominal cross-section 2.5 mm2 Protection degree: IP 20
Input 0...1 A / 0...5 A / 0...10 A AC switchable 50 / 60 Hz Voltage of measuring circuit 250 V AC Output 4...20 mA current loop Load resistance < 600 Ohm Strom >1 kOhm / voltage Transmission error < 0,5% v. E. Temperature coefficient 200 ppm / K Step response time typ. 700 ms Auxiliary power via output-side current loop Ambient temperature range 0 °C...+50 °C
Secure isolation EN 50178, 2-way isolation up to 6 kV Test voltage 4 kV input against output Rated voltage 300 V AC/DC at overvoltage category III and pollution degree 2 Approvals cULus, cULusEX C1D2, ATEX Zone 2
Type WAS1 CMA LP 1/5/10A EX
Short specification
Monitoring component for AC currents up to 10A with 4...20 mA loop feed and electrical isolation Current monitoring component in 22.5 mm width for recording 50/ 60 Hz AC currents 0...1 A / 0...5 A / 0...10 A. Input range can be selected using DIP switches. Power is fed to the component via the 4...20 mA current loop on the output side. The input and output circuits have 6 kV of electrical isolation. Approved for ATEX Zone2 and UL C1 D2 applications.
Monitoring component for AC currents up to 10A with 4...20 mA loop feed and electrical isolation Current monitoring component in 22.5 mm width for recording 50/ 60 Hz AC currents 0...1 A / 0...5 A / 0...10 A. Input range can be selected using DIP switches. Power is fed to the component via the 4...20 mA current loop on the output side. The input and output circuits have 6 kV of electrical isolation. Approved for ATEX Zone2 and UL C1 D2 applications.
Add-on housing for TS35 rail mounting Dimensions: L/W/H 72/ 22.5/ 92.4 mm Screw connection / Nominal cross-section 2.5 mm2 Protection degree: IP 20
Input 0...1 A / 0...5 A / 0...10 A AC switchable 50 / 60 Hz Voltage of measuring circuit 250 V AC Output 4...20 mA current loop Load resistance < 600 Ohm Strom >1 kOhm / voltage Transmission error < 0,5% v. E. Temperature coefficient 200 ppm / K Step response time typ. 700 ms Auxiliary power via output-side current loop Ambient temperature range 0 °C...+50 °C
Secure isolation EN 50178, 2-way isolation up to 6 kV Test voltage 4 kV input against output Rated voltage 300 V AC/DC at overvoltage category III and pollution degree 2 Approvals cULus, cULusEX C1D2, ATEX Zone 2
Type WAS1 CMA LP 1/5/10A EX
Short specification
Monitoring component for AC currents up to 10A with 4...20 mA loop feed and electrical isolation Current monitoring component in 22.5 mm width for recording 50/ 60 Hz AC currents 0...1 A / 0...5 A / 0...10 A. Input range can be selected using DIP switches. Power is fed to the component via the 4...20 mA current loop on the output side. The input and output circuits have 6 kV of electrical isolation. Approved for ATEX Zone2 and UL C1 D2 applications.
This function is provided via the external service provider https://supplyframe.com. By clicking on "Continue" you will be redirected to this page. This leads to a data transfer of personal data to non-European countries. Please check the data protection policy of the external website, for which Weidmüller assumes no responsibility and liability.